May 12, 2023Leave a message

Radiator: Fan bearing

The bearing type refers to the type of bearing used in air-cooled radiator fans. In mechanical engineering, there are many types of bearings, but there are only three types of bearings used in radiator products according to their basic working principles: sleeve bearing using sliding friction, ball bearing using rolling friction, and a mixture of two types of bearings. In recent years, major radiator manufacturers have introduced new technologies in the field of bearings, such as magnetic levitation bearings, fluid protection system bearings, liquid bearings, Laifu bearings, nano ceramic bearings, etc. These basic bearing forms have also been improved, and the basic working principles have not changed.
Oil bearing is a sleeve bearing with sliding friction, which uses lubricating oil as lubricant and drag reducing agent. In the initial use, it has low operating noise and manufacturing cost. However, this kind of bearing is severely worn, and its service life is far from that of ball bearing. Moreover, as this type of bearing is used for a long time, due to the use of oil seals (which are not possible for computer radiator products, usually ordinary paper oil seals), the lubricating oil will gradually evaporate, and dust will also enter the bearing, causing problems such as slow fan speed and increased noise. In severe cases, it can also cause eccentric fan vibration due to bearing wear. If these phenomena occur, either open the oil seal for refueling, or simply eliminate and purchase a new fan.
The single ball bearing (1 Ball+1 Sleeve Bearing) is an improvement on the traditional oil bearing. It adopts the combination of sliding friction and rolling friction. In fact, it is a way to reduce the cost of double ball bearings by matching one ball bearing with one oil bearing. Its rotor and stator are lubricated with balls and equipped with lubricating oil. It overcomes the problems of short lifespan and unstable operation of oil bearing, while the cost increase is extremely limited. The single ball bearing absorbs the advantages of oil bearing and double ball bearing, increasing the service life of the bearing to 40000 hours. The disadvantage is that after adding balls, the operating noise increases, but it is still smaller than the double ball bearing.
2 Ball Bearing is a comparative type of bearing that adopts the form of rolling friction and uses two ball bearings. There are several small steel balls in the bearing that revolve around the axis. When the fan or axis rotates, the steel balls follow suit. Because they are all spheres, the friction force is small and there is no problem of oil leakage. The advantage of double ball bearings is their long lifespan, which is approximately 50000-100000 hours; Good anti-aging performance, suitable for fans with high speed. The disadvantage of double ball bearings is their high manufacturing cost and high noise at the same speed level. The sealing performance of double ball wind bearings and hydraulic bearings is good, especially double ball bearings. The double ball bearing is completely embedded in the fan, and the rotating part does not come into direct contact with the outside world. In a sealed environment, the working environment of the bearing is relatively stable. Therefore, almost all large diameter fans with a speed of 5000 rpm use double ball bearings. However, due to its return oil circuit, the possibility of lubricating oil leakage is relatively low.
The representative manufacturer of Rifle Bearing technology is CoolerMaster, which has upgraded most of its traditional oil bearing fans to Rifle Bearing. As an improvement of traditional oil bearing, the Laifu bearing uses wear-resistant materials to make a high oil hollow bearing, reducing the friction between the bearing and the shaft core. The Laifu bearing also has a shaft core with reverse spiral grooves and oil blocking grooves, which will form a reverse flow when the fan is running, thereby avoiding oil loss and improving the bearing life. By adopting the above structure and components, the Laifu bearing fan greatly improves its oil and oil retention capacity, and reduces noise.
The name of Hydro Bearing is derived from HY (Hydrodynamic wave, fluid mechanics wave) PRO (Oil protection system, oil protection system). It is a product of the radiator and fan design manufacturer ADDA, and is also a product of several improvements on the basis of traditional oil bearing. The bearings and hydraulic bearings of the fluid protection system can be said to have the same goal in different ways. Both designs adopt some unique improvement measures, but the essence is the circulating oil system, and the performance in all aspects is basically the same. Usually, the product life can reach over 50000 hours.
Hydraulic Bearing is an improvement on oil bearing based on AVC * technology. The hydraulic bearing has a larger oil storage space than the oil bearing, and has a * loop type oil supply circuit. The working noise of the liquid supported fan has been significantly reduced, and its service life is also very long, reaching 40000 hours. Liquid bearing is essentially still an oil bearing. But after improvement, the lifespan of this type of bearing has been greatly extended compared to ordinary oil sealed bearings, and it inherits the advantages of oil bearing - low operating noise. At present, liquid bearing has been applied in AVC radiators, but not all AVC radiators use liquid bearing fans.
VAPO Bearing is an improvement of magnetic levitation technology by Sunon, which enhances the hardness of the oil bearing shaft sleeve and uses special materials. The inner surface of the bearing is also specially processed, which overcomes the disadvantage of high temperature resistance of oil bearing. In combination with magnetic levitation technology, the service life is greatly extended.
The motor of magnetic bearing is of magnetic system (MS) design. Its magnetic induction line is perpendicular to the magnetic levitation line, so the shaft core is parallel to the magnetic levitation line. Therefore, the weight of the rotor is fixed on the running track. The almost no-load shaft core is used to support the rotor in the direction of the anti magnetic levitation line, forming the whole rotor suspended in the air on the fixed running track. Therefore, magnetic levitation is actually only an auxiliary function and not an independent bearing form. Its specific application also needs to be combined with other bearing forms, such as magnetic levitation+ball bearing, magnetic levitation+oil bearing, magnetic levitation+vaporization bearing, and so on. This technology has not been recognized by European and American countries.
Nano Ceramic Bearing (NCB) is still essentially an oil bearing, which was first introduced by Foxconn in its products. Traditional oil bearing fans have severe wear and tear during use, and their reliability is low when used for a long time. Nano bearings have effectively overcome this problem: ceramic bearing technology uses special polymer materials and special additives to fully integrate, and the bearing core is made of special white oxide materials using stamping and sintering processes. The crystal particles have decreased from the previous 60um to 0.3um, with characteristics such as robustness, smoothness, and wear resistance. Nano ceramic bearings have strong high-temperature resistance and are not easily volatile, which greatly extends the service life of fans. The properties of nano bearings are similar to ceramics, and the smoother they are worn, the smoother they become. According to testing, the average service life of fans using nano ceramic bearings is over 150000 hours. This technology is not really nanotechnology, and the materials used are not truly nanoscale materials. It is simply using the term 'nano' to attract attention.

Send Inquiry

Home

Phone

E-mail

Inquiry