Mar 13, 2023Leave a message

Common sense of safe use of medical ventilator and centrifugal fan


As a kind of ventilation machinery, centrifugal fan is widely used not only in industry, but also in hospitals. Medical ventilator and centrifugal fan are developed according to the requirements of the special environment of the hospital. However, if the centrifugal fan is not used well, it may not work. Therefore, in this article, we will introduce the common sense of safe use of the centrifugal fan for medical ventilator.
What should we pay attention to when using the special centrifugal fan in hospital? How to use the special centrifugal fan for hospital to prolong the service life? Although professional centrifugal fan manufacturers will provide instructions, some customers do not know how to operate when they encounter unprofessional centrifugal fan manufacturers.
Before use, you should read the manual of the centrifugal fan of the medical ventilator, or grasp the common sense of the safe use of the medical centrifugal fan. Next, introduce the content of the common sense of the safe use of the hospital special centrifugal fan.
1. Proper installation of hospital special centrifugal fan
(1) Power supply voltage: the voltage fluctuation value should meet the national standard within+10%, otherwise some manufacturers' hospital special centrifugal fans cannot operate normally. If the voltage fluctuation value is above this, it is recommended to use a voltage stabilizer to meet the requirements of this grid.
(2) The ground wire should be firm: the wiring of the power supply in the room should fully meet the requirements. China's standard is three-phase four-wire system. Three-phase refers to the three phases of industrial electricity. When using three-phase electricity, the zero line and ground wire should be separated. More importantly, whether three-phase industrial electricity or not, general single-phase electricity can also be used. The ground wire should be reliable to avoid leakage, and the ground wire should never be connected to the heating pipe or water pipe.
(3) The ground should be flat and firm: for the special centrifugal fan for large hospitals, the floor at the installation site should be firm to ensure that the rotor of the centrifuge can work normally without sinking, and the ground should be flat and firm at the installation site.
(4) . Find the right level: find a relatively accurate small level ruler, open the centrifuge cover, find the right level on the main shaft, and adjust the screw of the adjusting bolts beside the four casters of the medical centrifuge to find the right level. Pay attention that no foot can fall empty.
2. Balance of the installation sample of the special centrifugal fan for the hospital
During the design and manufacture of centrifugal fans, the unbalance caused by the processing error of the rotor has been remedied by dynamic balance test, but all centrifugal fans have their allowable sample unbalance. In order to compete with other manufacturers in the index of maximum allowable unbalance limit of centrifuges, manufacturers of special centrifugal fans for hospitals try to give a larger value. At this higher value, the centrifugal fan can operate, but the unbalance force generated at this time suddenly impacts the bearing and bracket at the frequency of n times per minute, and the hospital special centrifugal fan is damaged. Therefore, for those expensive centrifugal fans, users should try to find out the balance and then centrifugal, which is good for the service life of centrifugal fans.
3 Clean up the accumulated water in the cavity of the centrifugal fan used in the hospital
When the centrifugal fan is running, it uses refrigeration. Due to the moisture in the air, it frosts in the centrifugal cavity, and turns into water after shutdown. Most of the low-speed and large-capacity medical centrifugal fans abroad do not have drainage holes, and the water in the centrifugal cavity is accumulating more and more. At this time, the user should remove the rotor and clean the water. When reinstalling the rotor, be sure to install it properly to avoid accidents.
4. The aluminum alloy of medical centrifugal fan shall not be corroded
The rotor of centrifugal fan is generally made of aluminum alloy. When it is corroded, its strength decreases, and it is easy to cause accidents. Aluminum alloy is susceptible to liquid corrosion. After cleaning, it should be dried with a hair dryer or inverted for a period of time before use. Some blood stations import centrifuges, but there are 6 plastic holders in 6 aluminum cups. The plastic holder should have a bloodletting bag, and avoid putting it directly in the aluminum cup. Pay attention to the test tube for cracks. If the test tube (especially the test tube used repeatedly) has cracks, never use it, otherwise the test tube will break during use, which will cause the rotor to lose its balance during rotation, and may cause serious accidents such as broken shaft.
5 Broken shaft accident of medical centrifugal fan
If the rotor is not properly placed or the unbalance of the loaded sample is too large, the medical centrifugal fan starts. Although modern imported centrifugal fans are equipped with unbalance protection, that is, when the unbalance exceeds a certain limit, the power shall be cut off automatically to stop the centrifuge. However, under the above circumstances, it is too late, and there will be malignant accidents. One of the malignant accidents is shaft breaking. Because of the sudden shaft breaking during high-speed rotation, the centrifugal rotor has no support, and it rotates and collides in the centrifugal cavity, which can make the whole centrifugal fan rotate 270 °. At this time, if there are people or equipment nearby, it will cause casualties and equipment damage.
To sum up, if the centrifugal fan of medical ventilator is to be used safely, these five specifications must be followed. The hospital is a very special place, and all its design should be for the health of patients. Therefore, the significance of safe use of medical ventilator and centrifugal fan is to ensure that patients can be cured smoothly and discharged healthily in the hospital.

Send Inquiry

Home

Phone

E-mail

Inquiry