Small forced draft fans are very common in our lives. As we all know, although small forced draft fans have brought a lot of convenience to our lives, the noise problem of small forced draft fans is also a headache for us. So why is the noise generated by small forced draft fans? The following is an introduction to the noise foundation of small forced draft fans.
1、 Overview
The essence of sound is fluctuation. The air under action vibrates. When the vibration frequency is between 20 and 20000 Hz, the sensation produced by acting on the eardrum membrane of a person is called sound. The sound source can be a vibration of a solid or a fluid (liquid or gas). The following are some sound related physical quantities.
1) Sound power level
Any sound source will radiate sound energy outward during operation. The sound energy radiated per unit time under stable conditions is called sound power W, and is measured in watts (W). Generally, it is expressed acoustically by sound power level, i.e
2) Sound intensity level and sound pressure level
The sound power of a sound source cannot be directly measured, so that the sound power can be calculated by measuring the sound pressure or sound intensity of the sound source. The sound pressure P or sound intensity I is also expressed as sound pressure level LP or sound intensity level LI, i.e
3) Octave Band and Sound Spectrum Characteristics
The sound that humans can hear generally refers to sound waves with frequencies ranging from 20 to 20000 Hz. In order to facilitate measurement, this frequency range is often divided into several small frequency bands or bands. The most commonly used methods in noise measurement are octave and one-third octave. Octave band refers to the frequency band determined by the ratio of two adjacent frequencies to be 2:1. The commonly used octaves specified in the international IEC specifications are shown in Table 1. A third octave is the division of an octave into three segments.
The frequency spectrum is a graph of sound pressure levels or sound power levels varying with frequency. Noise from small and medium-sized forced draft fans can be roughly divided into three categories: low-frequency noise with a center frequency of less than 500HZ at the highest sound pressure level in the frequency spectrum, intermediate frequency noise with a center frequency of 500~1000Hz at the highest sound pressure level, and high-frequency noise with a center frequency of greater than 1000Hz at the highest sound pressure level. The spectrum of a small forced draft fan is generally measured using a spectrum analyzer.
2、 Methods of testing sound
The sound pressure level and sound intensity level can be measured using a sound level meter or a sound intensity meter. Sound level meters are commonly used measuring instruments, but the use of sound intensity meters is not yet widespread.
In addition to the three basic parameters for measuring sound, it is also necessary to understand the frequency components of sound, which requires spectral analysis of sound. The commonly used sound frequency spectrum is octave frequency spectrum and 1/3 octave frequency spectrum. The sound spectrum is measured by a precision sound level meter or a dedicated frequency analyzer.
By measuring the sound spectrum, it is possible to analyze the frequency components of the sound source and take corresponding noise reduction measures to reduce the sound power level radiated outward.
Although the sound power can be indirectly obtained by measuring the sound pressure level. However, when measuring sound pressure levels, it is often difficult to accurately determine due to the impact of the test environment. In order to minimize the impact of the test environment, two near ideal laboratory testing methods have been created: the free sound field method and the reverberation sound field method.
When a sound source operates in a specific space, all the sound energy radiated by it is absorbed by the boundary without reflection, forming a specific law of sound propagation in this space. This particular space is called a free sound field. In laboratories that simulate free sound fields, fully anechoic or semi anechoic chambers are commonly used. Conversely, if the boundary of this particular space is a total reflection and silent energy absorption, there is also a specific law of acoustic wave propagation in this particular space. This particular space is called a reverberant sound field, and a reverberant chamber is commonly used in laboratories that simulate reverberant sound fields.
This article mainly introduces the reverberation chamber method.
If a sound source is provided in an enclosed empty chamber (reverberation chamber), after a period of time, a constant sound pressure level is generated in the chamber.
After cutting off the sound source, the sound does not immediately disappear, and the sound energy stored in space gradually decays, a process known as diffusion or reverberation. The reverberation time is defined as the attenuation of the sound energy density to 60 dB (i.e
10-6 times).
In a reverberation chamber, measuring a fully diffused sound field is called the diffusion sound field method. If the average sound pressure level of the diffusion sound field is LP, the corresponding sound power level is
In fact, it is impossible for the boundaries of a laboratory to achieve complete absorption or complete reflection of all frequencies. This difference specifies the accuracy requirements for measuring sound power levels in the laboratory (i.e., the allowable deviation requirements for sound pressure levels). Therefore, there must be a unified test specification, i.e., the standard for test methods. There are two types of standards: one is based on the standards specified by the International Organization for Standardization (ISO standards); The other is an industry standard specified by AMCA or ASHRAE in the United States. There are some differences between the two standards.
In summary, through the introduction of this article, we have learned more about the noise of small forced draft fans. Although these are only basic knowledge, they are of great significance for us to understand the causes of small blower noise and to prevent and control small blower noise, so we should learn.
Mar 30, 2023Leave a message
Maintenance Of Small Forced Draft Fans Can Generate Noise
Send Inquiry











